#SYNOLOGY CLOUD STATION DRIVE ACCESS SERIAL NUMBER#
#SYNOLOGY CLOUD STATION DRIVE ACCESS UPDATE#
#SYNOLOGY CLOUD STATION DRIVE ACCESS FULL#
#SYNOLOGY CLOUD STATION DRIVE ACCESS VERIFICATION#
#SYNOLOGY CLOUD STATION DRIVE ACCESS PASSWORD#

To find the you need to go to the album in your photos instance, and the id will be in the URL ex:, where 19 is the album id. You can find this id when using the media browser, when you hover over the NAS name, you get shown the simple name followed by the unique id ex: 192.168.0.100:5001 - 18C0PEN253705.

#SYNOLOGY CLOUD STATION DRIVE ACCESS SERIAL NUMBER#

is the Home Assistant ID for the NAS ( usually the serial number of the NAS). This media browser supports multiple Synology Photos instances. The media source URIs will look like media-source://synology_dsm///. Buttons Button rebootĪ media source is provided for your Synology Photos. Camerasįor each camera added in Surveillance Station, a camera will be created in Home Assistant. SwitchĪ switch is available to enable/disable the Surveillance Station Home mode. These sensors report if a drive has exceeded the maximum threshold for detected bad sectors and if a drive has dropped below the threshold for its remaining life. Similar to the normal disk sensors, there are binary sensors reporting each drive’s status.

#SYNOLOGY CLOUD STATION DRIVE ACCESS UPDATE#

The security status corresponds with the analysis of the DSM Security Advisor, e.g., an outOfDate state for the Update attribute not only reflects the update status of the installed DSM version but also the status of the installed DSM packages. Binary sensors General sensorsĮntity reporting the security status of the NAS. By default the total size and maximum disk temperature sensors are disabled. Volume sensorsĮntities reporting status, total size (TB), used size (TB), % of volume used, average disk temperature and maximum disk temperature for each volume inside the NAS. The SMART status sensor is disabled by default. Disk sensorsĮntities reporting the internal temperature, status (as shown in Synology DSM) and SMART status for each drive inside the NAS. The uptime sensor is disabled by default. General sensorsĮntities reporting the internal temperature and the uptime of the NAS. Both upload and download sensors are available. Network sensorsĮntities reporting the current network transfer rates of the NAS. These sensors include the total installed amount, the currently free amount and the % of memory used. Memory Utilisation sensorsĮntities reporting the current and combined memory and swap utilization of the NAS. By default the 1min load sensor is disabled. Available as current, 1min, 5min and 15min load sensors. These report the total CPU load for the entire NAS. There are also combined CPU load sensors. By default, only the User sensor is enabled. There are sensors the report the current CPU load, separated by User, System and others. As noted above, you do not need access to the DSM and Home Assistant will still be able to read statistics from your NAS.Įntities reporting the current and combined CPU utilization of the NAS. If you denied access to all locations and applications it is normal to receive a message indicating you do not have access to DSM when trying to login with this separate user.

#SYNOLOGY CLOUD STATION DRIVE ACCESS PASSWORD#

DSM will walk you through the process of setting up the one-time password for this user which you’ll then be able to use in Home Assistant’s frontend configuration screen. Make sure to log out of your “normal” user’s account and then login with the separate user you created specifically for Home Assistant.

#SYNOLOGY CLOUD STATION DRIVE ACCESS VERIFICATION#

If you have the “Enforce 2-step verification for the following users” option checked under Control Panel > User > Advanced > 2-Step Verification, you’ll need to configure the 2-step verification/one-time password (OTP) for the user you just created before the credentials for this user will work with Home Assistant. If you utilize 2-Step Verification or Two Factor Authentication (2FA) with your Synology NAS If you want to add cameras from Surveillance Station, the user needs application permission for Surveillance Station. It is still able to read the utilization and storage information using the API. By doing this, the user will not be able to login to the web interface or view any of the files on the Synology NAS. When creating the user, it is possible to deny access to all locations and applications. This is related to the fact that utilization information is stored in the core module. Separate User Configurationĭue to the nature of the Synology DSM API, it is required to grant the user admin rights. In this case, it is recommended to use NIC bonding instead or to deactivate SSDP.

#SYNOLOGY CLOUD STATION DRIVE ACCESS FULL#

Take full ownership of your data and pay no subscription fees.If you have two or more NICs with different IP addresses from the same subnet and SSDP is activated, this leads to problems with this integration, as the NAS is detected several times with different IPs and the integration always adopts the new “detected” IP address in its configuration and then reloads it. Access, share, and collaborate on your files from any devices, anywhere.

Synology cloud station drive access